*Deliveries are a 4 week time frame.

*Engineer Building, Anchor Bolt & Foundation plans with calculation are provided.

*All Steel Components & Labor are made in the USA!

  1. Primary framing (columns & rafters) are solid I-beam construction with a yield strength of 55,000 PSI and meet ASTM Specifications A-992.
  2. Secondary framing (purlin, girts, eave struts, angle and ā€œCā€ channel) are ASTM A-607 grade 55 with a minimum yield strength of 36,000 PSI.
  3. All buildings are fabricated under AISC (American Institute of Steel Construction).
  4. All framed openings are factory located.
  5. All secondary framing is punched & marked to match engineered plans. *A factory inventory list of parts is provided.
  6. All clips are welded solid for easy construction.
  7. Secondary girts & purlins overlap 3 feet.
  8. Sheeting angle is provided for gable.
  9. Flange bracing is provided.
  10. Base angle is provided.
  11. Roof wall panels are a minimum 26 gauge, ASTM 792 Grade 80 coil with 80,000 PSI yield strength.
  12. Trim is a minimum 26 gauge ASTM 792 grade 50 coil.
  13. *All trim is individually wrapped and placed in a cardboard box for protection.
  14. Colored panels & trim are covered by a 40 year factory warranty with 25 colors to choose from.
  15. Galvalume panels carry a 25 year warranty.
  16. *All sheets are blocked & banded with a cover sheet for protection.
  17. Roof panels are upgraded to a PBL (Purlin Bearing Leg) for support.
  18. Trim for the gables, corner, base, eaves and framed openings are provided.
  19. *All trim is hemmed to avoid sharp edges.
  20. Roll-up door casing trim is provided.
  21. Corrugated die formed ridge cap is provided.
  22. High strength bolts are provided.
  23.  *3/8 steel bracing cable is provided.
  24. Self-drilling screws with washer come with a lifetime warranty.
  25. Mastic sealant provided.
  26. Roll-up doors come with a 1 year factory warranty.
  27. All roll-up doors are wrapped & placed in a cardboard box to avoid damage.
  28. All roll-up doors are wind rated.

2. What Paint System do you use?

It is important to know that the paint system is manufactured by a reputable company. Kynar offers the best protection against chalking and fading. Siliconized polyester is the most widely used paint system and it mixes silicon with the paint to protect against chalk and fade. Although a polyester paint system is becoming less used, there are still companies that use it and it will have the lowest performance of the three paint systems.Polyester paint systems are generally reserved for economy panels or secondary panels.

3. What is the Thickness of your Paint?

The thicker the paint, the more protection you will have against chalking and fading. For prime material, we recommend that the primer and paint should be at least 1 millimeter thick in order to provide adequate protection. For economy and non-warranty panels, the thickness may be less.

4. What is the Hardness of your Metal?

Metal is made with "minimum yield strength." This affects the performance of the steel in regards to denting and bending. The lower the hardness, or tensile strength, the easier it is for the material to bend or dent. For optimal performance, panels should be rolled out of a minimum of grade 80 panels (also called Grade E). Trim should be bent out of a Grade 50 material (trim is bent at sharper angles and should be made out of a softer material). Many manufacturers carry only one type of inventory and this leads to either a softer panel that can show footprints, hail damage, or rock dents, or a harder trim that can crack and show rust quickly. Always ask what the "minimum" hardness is. This is the guaranteed hardness (some companies advertise a hardness that is above the guaranteed).

5. What is the Thickness of your Metal?

29 gauge and 26 gauge metals have a variey of thickness that fall into these gauge ranges. The thicker the panel, the sturdier it will be and the longer it will last. The recent trend is to offer a thinner panel to be able to give their customers a cheaper option, but many reputable manufacturers still offer an optimal thickness. We recommend the Prime 29 gauge material be at least .015 thickness for 29 gauge and .0185 for 26 gauge. Economy or secondary panels may be less. This thickness is before paint.

6. How Long have you been in Business?

With more and more metal manufacturers opening across the nation, it is becoming harder to find a manufacturer that has experience and longevity. The longer a manufacturer has been around, the better quality systems they will have established. They will also have better relationships with vendor and will be able to efficiently handle warranty claims should they arise.

Standard components included in all quin-co buildings

1. What Substrate do you use? If Galvanized, what Grade?

The substrate is the rust-inhibitor coating that is covering the steel but under the paint. AGalvalume substrate uses a mixture of aluminum and zinc to protect against rust, whereas a Galvanized substrate uses zinc. Galvalume may begin to show rust around the edges of the panel before a galvanized substrate, but the rust should stop when it comes in contact with the aluminum in substrate. A galvanized substrate will take a few years longer to show edge rust, but once the rust begins it could continue to corrode the entire panel. In non-agricultural applications, a galvalume substrate is comparable with a galvanized G90 coating and far superior to a Galvanized G60 coating. (The higher the number with galvanized, the more protectove coating.) Also, Galvalume-coated panels offer a "rust-through" warranty for 20 years, while the Galvanized-coated panel offers no such warranty.

6 questions to ask your metal building supplier